What is Boiling Liquid Expanding Vapour Explosion (BLEVE) on Gas Carrier Ships?

Just like Air Locks on Gas Carrier, a safety protection system between the deck (the hazardous zone) and the cargo compressor motor (gas free zone), the cargo tanks of gas carriers are also provided with various safety measures to prevent contact of cargo with the atmosphere and also to avoid cargo tanks from getting over pressurised.

Gas carrier’s cargo tanks are specially made of high strength and low thermal coefficient materials with insulation and safety systems. One of the essential safety measures in such cargo tanks is the pressure relief valve, which helps in avoiding over pressurisation of tanks and preventing rupture and damage of the same.

In gas ships, it is not the liquid which generally catches fire but it’s the vapour of the liquid which is more dangerous when evaporates at very low temperature. This results in Boiling Liquid Expanding Vapour Explosion (BLEVE).

What is Boiling Liquid Expanding Vapour Explosion (BLEVE)?

BLEVE is a vapour explosion which may result from a catastrophic failure of a tank structure, which was containing cargo liquid above the boiling point at nominal atmospheric pressure.

The cargo in the tanks of gas carrier is partially liquid and partially vapour in normal condition. However, when the tank structure collapses, the vapour tries to escape or leak through the opening, resulting in a decrease in the pressure inside the tank. These drastic lowering of pressure inside the cargo tank results in rapid boiling of liquid and increase in vapour formation.

The pressure of the escaping vapour becomes very high and leads to a shock wave or explosion in the presence of a fire source, completely destroying the tanks structure and surrounding areas.

The area that a BLEV explosion will cover entirely depends on the size, volume and weight of the container or hold in which the cargo is loaded. The quantity of liquid cargo that remains inside the tank at the instance of the BLEVE will also contribute to the magnitude of the explosion.

Do note that the BLEVE can occur even without a flammable substance. For e.g. liquid cargo stored in extreme colds such as liquid helium or other refrigerants or cryogens can also undergo similar conditions occurs under BLEVE; however, they are not usually considered a type of chemical explosion. If the material or cargo involved in BLEVE is toxic, a large area will be contaminated due to that.

Only if the substance involved is flammable, it is likely to form a cloud of fireball during BLEVE similar to a fuel-air explosion, also known as a vapour cloud explosion (VCE).

Related Read: Dangerous Engine Room Accidents On Ships

Prevailing Conditions for BLEVE

BLEVE will not occur in an instant. It will happen when certain conditions are fulfilled, i.e. in other words, warning signs are neglected. Following are the conditions which need to be present for a Boiling Liquid Expanding Vapor Explosion:

Liquid Cargo: Vapour alone cannot lead to BLEVE. A liquid cargo must be present inside the tank to make it happen. Even water can lead to BLEVE. However, there will be no fire as it is not flammable.
Pressurized container: The liquid cargo must be inside a tightly closed container or hold. A ventilated container may lead to BLEVE only if the vent mechanism becomes faulty, leading to pressure development inside the tank or hold.
Above Boiling Temperature: The temperature of the enclosed liquid cargo must be above its boiling point at atmospheric pressure to contribute to Boiling Liquid Expanding Vapor Explosion. When a pressurized cargo hold or tank is heated, the vapour pressure will increases. An elevated boiling point accompanies the increased vapour pressure.
Structure Failure: The liquid needs a path to escape from the pressurized tank and convert into vapour, which can only happen when there is a structural failure of the tank or hold.

Common Causes of BLEVE

The most common reason which leads to BLEVE is a fire near tanks containing gas cargo such as propane. Because of the high temperature of the surrounding, the tank temperature starts to increase and the inside of the tanks gets over pressurised. The high pressure inside the tank will be generally released by the relief valve.

However, if the pressure builds up rapidly because of high temperature and high rate of heating in the surrounding, the tank will collapse at the weaker point, exposing pressurised and flammable vapour to the naked flame and leading to Boiling Liquid Expanding Vapour Explosion.

Reason for Failure of Tank Structure

Improper maintenance of tanks

Corrosion of the tank structure

The relief valve of the tank is a malfunction or stuck

Mechanical damage to the tank

Material failure

Tank structure severely exposed to flame or fire

Different Phases of BLEVE

As stated earlier, BLEVE will not happen suddenly or if any one of the element explained earlier is missing. Following are the steps which can lead to BLEVE

Failure of the tank/hold: Tank failure may be due to different reasons which may lead to an increase in the internal pressure and failure of the weakest part of the tank
Phase transition: As the tank structure fails, a sudden depressurization of the liquified gas will occur. The liquid vapour mixture, which was in a thermodynamic saturated state with a higher temperature than its boiling point, will become superheated as the original tank/hold pressure decreases to atmospheric pressure in few milliseconds.
Splashing of liquid vapour mixture: As the temperature is above superheated limit temperature (SLT), fast bubble nucleation will initiate inside the tank leading to a violent splashing of liquid/vapour mixture out of the vessel into the atmosphere.
Explosion: As the depressurization occurs, along with an intense phase transition in the superheated state, the boiling of the liquid followed by bubble nucleation will together lead to an explosion.

BLEVE Warning Signs:

Ringing sound from the metal shell
discolouration of the tank structure
Flaking of small metal pieces
Bubble or bulge on the tank surface
A sudden increase in the tank pressure

Precautions to avoid BLEVE

Maintenance of the cargo tank at regular interval
Relief valve to be functional at all time
The size of the relief valve to be fitted should be as per the International Gas code
Emergency preparedness of all ship staff
During the gas cargo transfer, avoid general cargo, stores, compressed gas operation within the vicinity of the gas cargo operation
No oil or fuel bunkering operation should be carried out during or before the cargo operation
Keep checking the mooring lines to ensure the ship is well fastened to the pier/ dock
An LP-Gas detector shall be readily available for use at the berth
any cargo transfer during the night or dark hours should be done in the presence of ample lights, both in port and on the ship
The Connection area, stop valves etc. should be clearly marked and visible without any hindrance on their way while the cargo transfer is going on
Fire fighting equipment should always be present and accessible during the operation
Enough warning signs should be placed to ensure all the personnel (shore and ship staff) know about the cargo transfer operation and precautions to be taken
Always think of safety first

Watch the Video on BLEVE for better understanding:

Disclaimer: The authors’ views expressed in this article do not necessarily reflect the views of Marine Insight. Data and charts, if used, in the article have been sourced from available information and have not been authenticated by any statutory authority. The author and Marine Insight do not claim it to be accurate nor accept any responsibility for the same. The views constitute only the opinions and do not constitute any guidelines or recommendation on any course of action to be followed by the reader.

The article or images cannot be reproduced, copied, shared or used in any form without the permission of the author and Marine Insight.

Do you have info to share with us ? Suggest a correction